# Working With Multiple Objective

## Working With Multiple Objective

Of course, specifying a set of objectives is only the first step in solving a multi-objective optimization problem. The next step is to indicate how the objectives should be combined. As noted earlier, we support two approaches: blended and hierarchical.

A blending approach creates a single objective by taking a linear
combination of your objectives. You provide a weight for each
objective as an argument to `setObjectiveN`

. Alternatively, you
can use the ObjNWeight attribute,
together with ObjNumber. The
default weight for an objective is 1.0.

To give an example, if your model has two objectives, and , and if you give weights of and to them, respectively, then Gurobi would solve your model with a blended objective of .

You should avoid weights that are very large or very small. A very large weight (i.e., larger than ) may lead to very large objective coefficients, which can cause numerical difficulties. A very small weight (i.e., smaller than ) may cause the contribution from that objective to the overall blended objective to be smaller than tolerances, which may lead to that objective being effectively ignored.

Hierarchical Objectives

A hierarchical or lexicographic approach assigns a priority to each
objective, and optimizes for the objectives in decreasing priority
order. At each step, it finds the best solution for the current
objective, but only from among those that would not degrade the
solution quality for higher-priority objectives. You provide the
priority for each objective as an argument to `setObjectiveN`

.
Alternatively, you can use the
ObjNPriority attribute. Priorities
are integral, not continuous. Larger values indicate higher
priorities. The default priority for an objective is 0.

To give an example, if your model has two objectives, with priorities and , and objective weights 1.0 and -1.0. Assuming the optimal solution for the first objective has value , then the solver will find the solution that optimizes minus the second objective from among all solutions with objective for the first objective.

Allowing Multiple-Objective Degradation

By default, our hierarchical approach won't allow later objectives to degrade earlier objectives, subject to the user-given ending gap conditions for the optimization problem. More precisely, the base value used to define what solutions are acceptable for lower priorities objectives - for a minimization problem - is computed as:

where is the value of the best incumbent solution, is the value of the best proven lower bound for the problem, is the relative MIP gap, and is the absolute MIP gap, and the set of feasible solutions for the next objective will consider solutions whose objective value is at most that value.

This behavior can be relaxed for MIPs through a
pair of tolerances: a relative and an absolute tolerance. These are
provided as arguments to `setObjectiveN`

, or they can be set
using attributes ObjNRelTol and
ObjNAbsTol. By setting one of these
for a particular objective, you can indicate that later objectives are
allowed to degrade this objective by the specified relative or
absolute amount, respectively. In our earlier example, if the optimal
value for the first objective is , and if we set
`ObjNAbsTol`

for this objective to , then the second
optimization step would find the best solution for the second
objective from among all solutions with objective or better for
the first objective. Note that if you modify both tolerances, later
optimizations would use the looser of the two values (i.e., the one
that allows the larger degradation).

Objective degradations are handled differently for multi-objective LP
models. For LP models, solution quality for higher-priority objectives is
maintained by fixing some variables to their values in previous
optimal solutions. These fixings are decided using variable reduced
costs. The value of the `ObjNAbsTol`

parameter indicates the
amount by which a fixed variable's reduced cost is allowed to violate
dual feasibility, whereas the `ObjNRelTol`

parameter is simply
ignored.
If you want the MIP behavior, where the degradation is controlled
more directly, you can add a dummy binary variable to the model, thus
transforming it into a MIP. Solving the resulting multi-objective MIP
will be much more time consuming than solving the original multi-objective LP.

Combining Blended and Hierarchical Objectives

Actually, both weight and priority are always specified for each objective. This allows you to seamlessly combine the blended and hierarchical approaches. To understand how this works, we should first provide more detail on how hierarchical objectives are handled.

When you specify a different priority for each of objectives, the solver performs separate optimization steps. In each step, in decreasing priority order, it optimizes for the current objective multiplied by its ObjNWeight attribute, while imposing constraints that ensure that the quality of higher-priority objectives isn't degraded by more than the specified tolerances.

If you give the same priority to multiple objectives, then they will be handled in the same optimization step, resulting in fewer than total steps for objectives. More precisely, one optimization step is performed per distinct priority value, in order of decreasing priority, and all objectives with the same priority are blended together, using the weights for those objectives. This gives you quite a bit of flexibility when combining the blended and hierarchical approaches.

One subtle point when blending multiple objectives within a single
level in a hierarchical approach relates to the handling of
degradations from lower-priority levels. The objective degradation
allowed after a blended optimization step is the maximum absolute and
relative degradations allowed by each of the participating
objectives. For example, if we have three objectives with
`ObjNPriority`

equal to , and `ObjNRelTol`

equal to
and `ObjNAbsTol`

equal to , and if the best solution for the first priority objective is
, then the allowed degradation for the first priority objective is
.

Querying multi-objective results

Multiple objective values can be queried programmatically in all our APIs.
The basic notion is that you have to specify for which multi objective
you want to query information (by setting the parameter
ObjNumber).
Furthermore, you can also specify for which solution you want to query
this information (by setting the parameter
SolutionNumber).
For example, in Python you can do the following:

# Read and solve a model with multiple objectives m = read('input.mps') m.optimize() # get the set of variables x = m.getVars() # Ensure status is optimal assert m.Status == GRB.Status.OPTIMAL # Query number of multiple objectives, and number of solutions nSolutions = m.SolCount nObjectives = m.NumObj print('Problem has', nObjectives, 'objectives') print('Gurobi found', nSolutions, 'solutions') # For each solution, print value of first three variables, and # value for each objective function solutions = [] for s in range(nSolutions): # Set which solution we will query from now on m.params.SolutionNumber = s # Print objective value of this solution in each objective print('Solution', s, ':', end='') for o in range(nObjectives): # Set which objective we will query m.params.ObjNumber = o # Query the o-th objective value print(' ',m.ObjNVal, end='') # print first three variables in the solution n = min(len(x),3) for j in range(n): print(x[j].VarName, x[j].Xn, end='') print('') # query the full vector of the o-th solution solutions.append(m.getAttr('Xn',x))